Making A Camera Studio Stand

studio camera stand

I have been using a tripod in the workshop to film and take pictures of my projects for years now.  This has always got in the way and taken too long to setup different shots, but a studio camera stand is extremely expensive. I thought I could have a go at making one for a fraction of the price….

I started by gathering the parts I needed:

Some scraps of wood (which I already had)

Scaffold pole and basket

4 casters

Manfrotto magic arm

Manfrotto super clamp

Manfrotto stud

Camera ball head

(A lot of the tools and materials I use can be found on my Amazon page.)

https://www.amazon.co.uk/shop/badgerworkshop

magic arm
cutting wood for camera stand
cutting wood for studio camera stand

The first thing I did was trim the pieces of wood to all the same length on the mitre saw.

marking wood
overlapping wood
finding centre of wood

I wanted to join the two pieces of wood together in a cross, so I marked out the point where they overlapped. I then marked out the centre point on the wood.

raising the table saw blade
setting blade hight

I raised the blade on the table saw until it reached the centre mark, then used the mitre gauge to push the wood through the saw, and nibble away the waste material on both pieces of wood.

nibbling away waste wood
testing the fit
cutting away waste wood
tapping into place

With both the slots cut, I was able to conduct a test fit. I was happy with the fit, so I moved on to fitting some casters.

fitting casters

The casters could simply be fitted to the bottom of the wood, but I wanted them to be recessed.  I marked out where I wanted the recess to be, then took the wood back to the table saw to cut away the waste material.

making camera stand
table saw cut
glueing camera stand
fitting camera stand
clamping camera stand

With the cuts made, I was able to use some PVA wood glue to attach the pieces together and get them clamped up.

fitting pole for camera stand

I wanted the scaffold pole to fit into the centre of the cross, so I marked out the centre point, and purchased a Forstner drill bit the same size as the pole. I used this to drill a hole 40mm deep.

making centre of studio stand
using drill press
forstner drill bit
drill shavings

I gave the cross a quick sand down, then positioned the bracket for the pole over the drilled hole, and marked out where the screws needed to go.  I then drilled a couple of pilot holes to accept the screws.

sanding camera studio stand
marking hole
drilling camera stand
staining with india ink
india ink on pine

To offer some protection (and to make it look cool) I stained the wood black using India ink then applied some Danish oil.

pouring danish oil
washer on wood screw
applying danish oil
screwing on casters

The craters come with holes larger than the heads of my screws, so I slipped a washer over them. I was then able to drive them into the wood, fixing the casters into place.

scaffold braket

The bracket I had for the scaffold pole won’t allow the pole to slide all the way through it – I needed it to go all the way through, slipping into the hole I drilled in the wood. I used a step drill to widen the base, allowing the pole to slide through.

step drill
tape on pole
drilling scaffold bracket
fitting pole into camera studio stand

When I test-fitted the pole in the hole, it was a little looser than I wanted.   I wrapped some tape around the base, which made it fit snugly in the hole.

fitting bracket to camera stand

I slid the bracket down the hole and screwed it into the base. I then tightened up the grub screws, locking the pole into place.

installing the camera studio stand
making studio camera stand
ball head on magic arm
fitting super clamp
fitting magic arm into super clamp

I fit the stud onto the end of the magic arm and screwed the ball head into place. The super clamp was fitted to the pole, and the arm locked into the clamp.

camera on studio stand
studio stand homemade

That’s it! This should make life much easier. The arm has one big lever that – when loosened – makes all three joints on the arm go loose. The camera can then be moved into the desired position and locked into place by tightening the lever.

For more information, please watch the video below and subscribe to me on YouTube for a new project every week. 

How I made a oak and leather kitchen towel holder

kitchen towel holder

I needed a kitchen towel holder, but – as I am a little short of worktop space – I wanted one that could hang on the wall. As I had already made a couple of other bits for the kitchen from oak, I decided to keep to that theme.

dowel for kitchen towel
dewalt dws777
cutting wood for towel holder

I got a length of oak dowel and a scrap of board, which I cut to a bit longer than the paper towel. I then ripped the board down on the table saw to the width I wanted.

ripping wood for towel holder
strap for kitchen towel holder
cutting leather strap
strap cutter

To attach the dowel to the board, I decided to use leather straps. Using my leather strap cutter, I cut a couple of 1 inch wide straps, but you could just purchase some leather already cut into strips.

marking strap position
setting blade hight
cross cut sled
cutting slots

I wanted to attach these straps to the back of the board, and have them recessed into it. I setup my crosscut sled on the table saw, then raised the blade up to the height of the strap folded over. I could then nibble away a 1 inch slot at either end of the board.

cleaning up slots
adding a round over

The slots needed a bit of a clean up with a chisel, then I used the router to round over the edges on the front of the board.

using pillar drill
brass inserts in towel holder
danish oil on towel holder

On either end of the board I instilled some brass screw inserts, that I could use to fix it to the wall. With those fitted, it was time to apply some finish. I went for hard wax oil to match the knife rack I made in the previous post.

leather on towel holder
cutting leather strap
dewalt drill
screwing strap on towel holder

When the finish dried, I was able to install the leather straps. I folded them over and positioned then into the slots, and used a knife to trim off any excess. To hold them in place, I drove some screws through the leather and into the oak.

pulling kitchen towel

That’s it, all done! Please watch the video below for more information on how I made this, along with a matching magnetic knife rack.

Pour Over Coffee Maker

pour over coffee maker

I will start with the caveat that I’m not a big coffee drinker – I like to start my day with a nice mug of strong tea.  But occasionally I have guests over, and it would be nice to be able to offer them something better than instant coffee. The trend seems to be to get one of those pod-based machines, but I don’t need more plastic in my life, and I always prefer a low tech option. After a bit of research, the pour-over coffee seemed to be the way to go.

 

I started by making a couple of purchases: a ceramic cone to hold the filter papers; and a glass jug to catch the coffee.   I got both of these from Amazon and here is an affiliate link if you wish to look at them:

https://www.amazon.co.uk/shop/badgerworkshop?listId=6RNE59VODQ4H&ref=idea_share_inf

Once I received the two items, I was able to sketch out a plan for the build. My idea was to make a brass stand to hold the two parts, with bits of walnut for them to sit on.

coffee jug sketching out a design

bevel gauge With the plan drawn out, you can see how the jug will fit into the frame and the filter on top. The angles are arbitrary and I just went with what looked good while still fitting around the jug.

I set my bevel gauge to the drawing and used it to set the angle on my metal bender. 

metal bender bending metal

Bent brass

Using my plan as reference, I marked on some brass bar where the bends for the top needed to go. I used 3mm by 19mm brass bar, which was readily available on Ebay. I could then line my marks up on the bender and make the bends to the desired angle.  (NOTE: Brass is pretty soft and it would be possible to make the bend just using a vice but as I had the machine I used it.)

If you fancy a metal bender for yourself ( and who would not? ) here is a link to the tools I use: https://www.amazon.co.uk/shop/badgerworkshop

With both bends done on two pieces of brass, I checked them against my plans – they were close enough. 

bending brass bent brass bar

Each piece of brass then needed two more bends to make the base. The base was not quite flat, but I knew this would get pulled into shape when the wood is added.

glueing walnut walnut pannel

I did not have any walnut wide enough for this project to I glued up some off-cuts to make a couple of panels.

making the centre drilling with a hole saw adding a chamfer adding a chamfer walnut

When they dried, I cut them to size on the mitre saw, and marked out the centre on the one that was going to be the top.  I then found a hole saw big enough to accommodate the ceramic cone and drill through the wood on the centre mark.

To soften the edges a little, I used a chamfer bit in my router table, but the edges could easily be rounded over with some sanding.

setting blade hight cutting a groove fitting the brass oil on walnut

The wood needed a groove cut in to accommodate the brass, so I set the height of the table saw blade to the thickness of the brass, and made several cuts to remove the waste material.  This allowed the brass to sit nicely in the recess.

As kitchen items get a bit of abuse, I finished the wood with a hard wax oil, as these are very hard-wearing.

While I was waiting for the finish to dry, I used the time to drill and countersink some holes into the brass for screws, so I could attach it to the wood.  When it had finally dried ( hard wax oil takes a while ) I was able to finally get all the bits screwed together.

Drilling brass brass and walnut

brass on walnut

Then it was all finished! A filter goes in the top, and gets a couple of scoops of ground coffee, then almost-boiling* water gets poured over.  All I need now are some visitors so I can try this out…

*water should be just off the boil, to avoid burning the coffee, which can make it taste bitter.

making pour over coffee coffee red mug

brass and walnut coffee maker pour over coffee brass and walnut

If you enjoyed this build and would like some more information, please watch this video and consider subscribing to me on YouTube.  I post a new project each week.

Making A Foot Stool

oak foot stool
Sketching a design

Like most people, I have my favourite chair, but I thought it might be nice to be able to put my feet up. The solution?   I decided to make a foot stool. 

I like to keep my plans quite loose, but I drew a rough sketch of what I wanted. I looked through the timber I had on hand, and decided to use some off-cuts of oak beam I had. 

I used the planer to clean up the faces of the wood, then I started ripping it down on the table saw. 

resawing oak

This wood was 8” thick, so I took a series of cuts, working from both sides and raising the blade each time until I had cut all the way through. I then cut the wood into square sections and trimmed them all to the same length on the mitre saw. 

sawing wood Dewalt mitre saw

 

 

I wanted the legs to have a taper to them, cut on two faces. I marked out where I wanted the taper to go, then made a jig for the table saw to cut them. (If you want to see how I made the jig, please watch the video at the bottom of this post for more information.) 

woodworker measuring

With all the tapers cut, I was able to lay out the legs and determine the sizes the aprons needed to be.  To make them, I ripped down some more oak on the table saw, and cut it to length on the mitre saw. 

cutting oak cutting oak

To join everything together, I decided to use oak dowels. (I have this Triton dowel joiner, which you can find on my Amazon page if you are interested.

https://www.amazon.co.uk/shop/badgerworkshop

If you don’t have a machine like this, a drill and simple doweling jig would work just as well.) I drilled holes into all the mating pieces, then tapped the dowels into place with some PVA wood glue. 

Triton dowel jointer

Making a foot stool

I dabbed some glue onto the faces of the joint and into the corresponding holes, then slid all the bits together.  With all the joints in place, I made sure everything was square and got it clamped up. 

Clamping wood

When the glue was dry, I removed the clamps. I sanded it down, and applied a coat of my favourite Danish finish oil. 

danish oil on oak sanding  oak

 

cutting foam

While I waited for the finish to dry, I started work on the cushioned top. I cut a piece of foam to slightly larger than the base using my bandsaw, but a serrated knife would work as well. 

 

festool track saw

I needed a base for the foam to sit on, so I used my track saw to cut down some 18mm plywood to the same size as the foam. 

upholstering a stool

I placed the foam on some wadding and cut around the foam, leaving a border wide enough to fold the wadding over the foam and plywood – I attached the wadding to the ply using a staple gun. I have not done much upholstery work, so this involved some guess work, but a staple gun makes life so much easier. 

upholstering a foot stool

I lay out some fabric and cut around it in a similar way to the wadding, and also attached this using the staple gun. 

stable gun upholstery

To prevent the stool from scratching my floor, I added some plastic feet to the bottom of each leg.

installing rubber feet

Woodworker

To the inside of the base, I attached some L shaped brackets. I then positioned the base onto the cushioned pad and screwed through the brackets to attach the two parts together.   

oak foot stool foot stool

That’s it all done!   All that’s left now, is to put my feet up. I hope you enjoyed this build – if you would like more information then please watch the video below.